"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 17.7 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 80 mA, Type of current: Alternating current (AC), Inrush current: 15.6 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. number of lamps on LS switch B10 A: 100, Max. number of lamps on LS switch B10 A - KVG/VVG without compensation: 75, Max. number of lamps on LS switch B10 A - KVG/VVG with compensation: 20, Max. number of lamps on LS switch B16 A: 160, Max. number of lamps on LS switch B16 A - KVG/VVG without compensation: 120, Max. number of lamps on LS switch B16 A - KVG/VVG with compensation: 24, Harmonic content: 18 %, Power factor ?: 0.90Photometric data: Luminous flux: 2160 lm, Luminous efficacy: 122 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Warm white, Color temperature: 3000 K, Color rendering index Ra: 80, Light color: 830, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 1212.00 mm, Length with base but without base pin: 1200.00 mm, Diameter: 26.00 mm, Product weight: 175.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 85 °C, Operating temperature according to IEC 62717: 50 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: E, Energy consumption: 18.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Lighting technology used: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-adjustable light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SI

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 8.8 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 40 mA, Type of current: Alternating current (AC), Inrush current: 10.0 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 60, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 61, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 27, Max. Number of lamps on LS switch B16 A: 75, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 76, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 34, Harmonic content: 16.5 %, Power factor ?: 0.90Photometric data: Luminous flux: 1200 lm, Luminous efficacy: 136 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool daylight, Color temperature: 6500 K, Color rendering index Ra: 80, Light color: 865, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 908.00 mm, Length with base but without base pin: 900.00 mm, Diameter: 26.00 mm, Product weight: 143.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 9.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Lighting technology used: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature:

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 17.7 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 80 mA, Type of current: Alternating current (AC), Inrush current: 15.6 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 100, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 75, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 20, Max. Number of lamps on LS switch B16 A: 160, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 120, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 24, Harmonic content: 18 %, Power factor ?: 0.90Photometric data: Luminous flux: 2400 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool white, Color temperature: 4000 K, Color rendering index Ra: 80, Light color: 840, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 1212.00 mm, Length with base but without base pin: 1200.00 mm, Diameter: 26.00 mm, Product weight: 175.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 85 °C, Operating temperature according to IEC 62717: 50 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 18.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Lighting technology used: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SI

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 6.3 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 28 mA, Type of current: Alternating current (AC), Inrush current: 9.2 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 171, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 100, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 22, Max. Number of lamps on LS switch B16 A: 214, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 160, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 26, Harmonic content: 17 %, Power factor ?: 0.90Photometric data: Luminous flux: 765 lm, Luminous efficacy: 121 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Warm white, Color temperature: 3000 K, Color rendering index Ra: 80, Light color: 830, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 732.00 mm, Length with base but without base pin: 720.00 mm, Diameter: 26.00 mm, Product weight: 110.00 gTemperatures & Operating conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 75 °C, Operating temperature according to IEC 62717: 40 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: E, Energy consumption: 7.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Protection class: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 7.4 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 33 mA, Type of current: Alternating current (AC), Inrush current: 8 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 69, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 68, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 30, Max. Number of lamps on LS switch B16 A: 87, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 86, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 37, Harmonic content: 16.2 %, Power factor ?: 0.90Photometric data: Luminous flux: 1000 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool white, Color temperature: 4000 K, Color rendering index Ra: 80, Light color: 840, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 603.00 mm, Length with base but without base pin: 600.00 mm, Diameter: 26.00 mm, Product weight: 97.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 8.00 kWh/1000h, Protection class: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Unbundled or bundled light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Envelope: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_VALU

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Protection class: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 4.8 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 21 mA, Type of current: Alternating current (AC), Inrush current: 8 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 102, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 120, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 45, Max. Number of lamps on LS switch B16 A: 128, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 150, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 56, Harmonic content: 18.5 %, Power factor ?: 0.90Photometric data: Luminous flux: 585 lm, Luminous efficacy: 121 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Warm white, Color temperature: 3000 K, Color rendering index Ra: 80, Light color: 830, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 451.00 mm, Length with base but without base pin: 438.00 mm, Diameter: 26.00 mm, Product weight: 75.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 76 °C, Operating temperature according to IEC 62717: 53 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: E, Energy consumption: 5.00 kWh/1000h, Protection class: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_V

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 4.8 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 21 mA, Type of current: Alternating current (AC), Inrush current: 8 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 102, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 120, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 45, Max. Number of lamps on LS switch B16 A: 128, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 150, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 56, Harmonic content: 18.5 %, Power factor ?: 0.90Photometric data: Luminous flux: 650 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool white, Color temperature: 4000 K, Color rendering index Ra: 80, Light color: 840, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 451.00 mm, Length with base but without base pin: 438.00 mm, Diameter: 26.00 mm, Product weight: 75.00 gTemperatures & Operating conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 76 °C, Operating temperature according to IEC 62717: 53 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 5.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_V

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Protection class: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 4.8 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 21 mA, Type of current: Alternating current (AC), Inrush current: 8 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 102, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 120, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 45, Max. Number of lamps on LS switch B16 A: 128, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 150, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 56, Harmonic content: 18.5 %, Power factor ?: 0.90Photometric data: Luminous flux: 650 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool daylight, Color temperature: 6500 K, Color rendering index Ra: 80, Light color: 865, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 451.00 mm, Length with base but without base pin: 438.00 mm, Diameter: 26.00 mm, Product weight: 75.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 76 °C, Operating temperature according to IEC 62717: 53 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 5.00 kWh/1000h, Protection class: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature:

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 7.4 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 33 mA, Type of current: Alternating current (AC), Inrush current: 8 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 69, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 68, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 30, Max. Number of lamps on LS switch B16 A: 87, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 86, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 37, Harmonic content: 16.2 %, Power factor ?: 0.90Photometric data: Luminous flux: 900 lm, Luminous efficacy: 121 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Warm white, Color temperature: 3000 K, Color rendering index Ra: 80, Light color: 830, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 603.00 mm, Length with base but without base pin: 600.00 mm, Diameter: 26.00 mm, Product weight: 97.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: E, Energy consumption: 8.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_VALUE

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 7.4 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 33 mA, Type of current: Alternating current (AC), Inrush current: 8 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 69, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 68, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 30, Max. Number of lamps on LS switch B16 A: 87, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 86, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 37, Harmonic content: 16.2 %, Power factor ?: 0.90Photometric data: Luminous flux: 1000 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool daylight, Color temperature: 6500 K, Color rendering index Ra: 80, Light color: 865, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 603.00 mm, Length with base but without base pin: 600.00 mm, Diameter: 26.00 mm, Product weight: 97.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 8.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-adjustable light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SIN

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 8.8 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 40 mA, Type of current: Alternating current (AC), Inrush current: 10.0 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 60, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 61, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 27, Max. Number of lamps on LS switch B16 A: 75, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 76, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 34, Harmonic content: 16.5 %, Power factor ?: 0.90Photometric data: Luminous flux: 1080 lm, Luminous efficacy: 122 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Warm white, Color temperature: 3000 K, Color rendering index Ra: 80, Light color: 830, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 908.00 mm, Length with base but without base pin: 900.00 mm, Diameter: 26.00 mm, Product weight: 143.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: E, Energy consumption: 9.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-adjustable light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 8.8 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 40 mA, Type of current: Alternating current (AC), Inrush current: 10.0 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 60, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 61, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 27, Max. Number of lamps on LS switch B16 A: 75, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 76, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 34, Harmonic content: 16.5 %, Power factor ?: 0.90Photometric data: Luminous flux: 1200 lm, Luminous efficacy: 136 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool white, Color temperature: 4000 K, Color rendering index Ra: 80, Light color: 840, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 908.00 mm, Length with base but without base pin: 900.00 mm, Diameter: 26.00 mm, Product weight: 143.00 gTemperatures & Operating conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 9.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SINGLE_

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easier, faster and safer lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 10.3 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 45 mA, Type of current: Alternating current (AC), Inrush current: 8.4 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 71, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 72, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 31, Max. Number of lamps on LS switch B16 A: 89, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 90, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 39, Harmonic content: 15.2 %, Power factor ?: 0.90Photometric data: Luminous flux: 1260 lm, Luminous efficacy: 122 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Warm white, Color temperature: 3000 K, Color rendering index Ra: 80, Light color: 830, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 1060.00 mm, Length with base but without base pin: 1050.00 mm, Diameter: 26.00 mm, Product weight: 155.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: E, Energy consumption: 11.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SING

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 10.3 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 45 mA, Type of current: Alternating current (AC), Inrush current: 8.4 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 71, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 72, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 31, Max. Number of lamps on LS switch B16 A: 89, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 90, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 39, Harmonic content: 15.2 %, Power factor ?: 0.90Photometric data: Luminous flux: 1400 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool white, Color temperature: 4000 K, Color rendering index Ra: 80, Light color: 840, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 1060.00 mm, Length with base but without base pin: 1050.00 mm, Diameter: 26.00 mm, Product weight: 155.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 11.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Unbundled or bundled light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature: SING

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 10.3 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 45 mA, Type of current: Alternating current (AC), Inrush current: 8.4 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 71, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 72, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 31, Max. Number of lamps on LS switch B16 A: 89, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 90, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 39, Harmonic content: 15.2 %, Power factor ?: 0.90Photometric data: Luminous flux: 1400 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool daylight, Color temperature: 6500 K, Color rendering index Ra: 80, Light color: 865, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker metric (Pst LM): 1, Metric for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 1060.00 mm, Length with base but without base pin: 1050.00 mm, Diameter: 26.00 mm, Product weight: 155.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 80 °C, Operating temperature according to IEC 62717: 54 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 11.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the Regulation on energy consumption labeling EU 2019/2015: Used lighting technology: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-adjustable light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature

"Product benefits: Energy savings of up to 72 per cent (compared to T8 fluorescent lamps). Simple, quick and safe lamp replacement, with or without rewiring. No sagging thanks to glass technology. Very high switching durability. Full brightness without a warm-up phase, making it ideally suited for use with sensor systems. Also suitable for operation at low temperatures Product features: LED replacement for conventional T8 fluorescent lamps with G13 base in ballast-operated luminaires or at mains voltage. Single and tandem operation with a conventional ballast (versions ? 0.9 m). Glass tube. Long service life of up to 50,000 hours. Uniform illumination. Mercury-free and RoHS-compliant. Protection class: IP20. Low flicker in accordance with EU 2019/2020 (SVM ≤ 0.4 / PstLM ≤ 1)Technical specifications: Suitable for operation with low-loss and conventional ballastsLegal notice: When replacing a T8 fluorescent lamp, the overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for use with electronic ballasts. Use in outdoor applications is possible in suitable damp-proof luminaires in accordance with the data sheet and installation instructions. Not suitable for emergency lighting. Disconnect from the mains before installation.Electrical data: Rated power: 6.3 W, Rated voltage: 220–240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 28 mA, Current type: Alternating current (AC), Inrush current: 9.2 A, Suitable for DC operation: Yes, DC input voltage: 186–260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. number of lamps on circuit breaker B10 A: 171, Max. number of lamps on circuit breaker B10 A – KVG/VVG without compensation: 100, Max. number of lamps on circuit breaker B10 A – KVG/VVG with compensation: 22, maximum number of lamps on circuit breaker B16 A: 214, Max. number of lamps on circuit breaker B16 A – KVG/VVG without compensation: 160, Max. number of lamps on circuit breaker B16 A – KVG/VVG with compensation: 26, Harmonic content: 17 %, Power factor ?: 0.90Photometric data: Luminous flux: 851 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of rated life: 0.70, Colour temperature (designation): Cool white, colour temperature: 4000 K, colour rendering index Ra: 80, light colour: 840, standard deviation of colour matching: ?6 sdcm, rated LLMF at 6,000 h: 0.80, flicker parameter (Pst LM): 1, stroboscopic effect parameter (SVM): 0.4Illumination data: Beam angle: 190°, Warm-up time (60 %): ‹ 0.50 s, Start-up time: < 0.5 sDimensions & weight: Overall length: 732.00 mm, Length including base but excluding base pin: 720.00 mm, Diameter: 26.00 mm, Product weight: 110.00 gTemperatures & operating conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measurement point tc: 75 °C, Operating temperature according to IEC 62717: 40 °CService life: L70/B50 service life at 25 °C: 50,000 h, number of switching cycles: 200,000, luminous flux retention at end of service life: 0.70, nominal lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Applications: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 7.00 kWh/1,000 h, Protection rating: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTICS DATA: Storage temperature range: -20…+80 °CData in accordance with the Energy Labelling Regulation (EU) 2019/2015: Lighting technology used: LED, Unfocused or focused light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Light source base (or other electrical interface): G13, Networked light source (CLS): No, Colour-adjustable light source: No, Enclosure: No, High-luminance light source: No, Anti-glare shield: No, Similar colour temperature: SINGLE_

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 6.3 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 28 mA, Type of current: Alternating current (AC), Inrush current: 9.2 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 171, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 100, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 22, Max. Number of lamps on LS switch B16 A: 214, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 160, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 26, Harmonic content: 17 %, Power factor ?: 0.90Photometric data: Luminous flux: 851 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool daylight, Color temperature: 6500 K, Color rendering index Ra: 80, Light color: 865, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measurement value (Pst LM): 1, Measurement value for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 732.00 mm, Length with base but without base pin: 720.00 mm, Diameter: 26.00 mm, Product weight: 110.00 gTemperatures & Operating Conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at measuring point tc: 75 °C, Operating temperature according to IEC 62717: 40 °CService Life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 7.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Lighting technology used: LED, Non-directional or directional light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature:

"Product advantages: Energy saving of up to 72 % (compared to T8 fluorescent lamp). Easy, fast and safe lamp replacement with or without rewiring. No sagging thanks to glass technology. Very high switching strength. Full brightness without warm-up phase, therefore ideally suited in combination with sensors. Also suitable for operation at low temperaturesProduct properties: LED replacement for conventional T8 fluorescent lamps with G13 base in KVG light fittings or at mains voltage. Single and tandem operation on conventional control gear (versions ? 0.9 m). Tube made of glass. Long service life of up to 50,000 h. Homogeneous illumination. Mercury-free and RoHS-compliant. Degree of protection: IP20. Flicker-free according to EU 2019/2020 (SVM ? 0.4 / PstLM ? 1)Technical equipment: Suitable for operation with low-loss and conventional control gearLegal notice: When replacing a T8 fluorescent lamp, overall energy efficiency and light distribution depend on the design of the system.Safety instructions: Not suitable for operation with electronic control gear. Use in outdoor applications is possible in suitable damp room light fittings according to data sheet and installation instructions. Not suitable for emergency lighting. Disconnect mains power before installation.Electrical data: Rated power: 17.7 W, Rated voltage: 220…240 V, Operating mode: KVG/VVG, Mains voltage, DC, Rated current: 80 mA, Type of current: Alternating current (AC), Inrush current: 15.6 A, Suitable for DC operation: Yes, Input voltage DC: 186…260 V, Operating frequency: 50/60 Hz, Mains frequency: 50/60 Hz, Max. Number of lamps on LS switch B10 A: 100, Max. Number of lamps on LS switch B10 A - KVG/VVG without compensation: 75, Max. Number of lamps on LS switch B10 A - KVG/VVG with compensation: 20, Max. Number of lamps on LS switch B16 A: 160, Max. Number of lamps on LS switch B16 A - KVG/VVG without compensation: 120, Max. Number of lamps on LS switch B16 A - KVG/VVG with compensation: 24, Harmonic content: 18 %, Power factor ?: 0.90Photometric data: Luminous flux: 2400 lm, Luminous efficacy: 135 lm/W, Luminous flux maintenance at the end of the rated life: 0.70, Light color (designation): Cool daylight, Color temperature: 6500 K, Color rendering index Ra: 80, Light color: 865, Standard deviation of color matching: ?6 sdcm, Rated LLMF at 6,000 h: 0.80, Flicker measure (Pst LM): 1, Measure for stroboscopic effects (SVM): 0.4Lighting data: Radiation angle: 190 °, Warm-up time (60 %): ‹ 0.50 s, Start time: < 0.5 sDimensions & Weight: Overall length: 1212.00 mm, Length with base but without base pin: 1200.00 mm, Diameter: 26.00 mm, Product weight: 175.00 gTemperatures & Operating conditions: Ambient temperature range: -20…+45 °C, Maximum temperature at the measurement point tc: 85 °C, Operating temperature according to IEC 62717: 50 °CService life: Service life L70/B50 at 25 °C: 50000 h, Number of switching cycles: 200000, Luminous flux maintenance at the end of maintenance: 0.70, Rated lamp survival factor at 6,000 h: ? 0.90Additional product data: Base (standard designation): G13, Mercury content of the lamp: 0.0 mg, Mercury-free: Yes, Product note: Available from June 2026Application possibilities: Dimmable: NoCertificates & Standards: Energy efficiency class: D, Energy consumption: 18.00 kWh/1000h, Degree of protection: IP20, Standards: CE; EAC; UKCA, Photobiological risk group according to EN62778: RG0Country-specific information: Order number: LEDTUBE T8 EM VLOGISTIC DATA: Storage temperature range: -20…+80 °CData according to the regulation on energy consumption labeling EU 2019/2015: Lighting technology used: LED, Unbundled or bundled light: NDLS, Mains voltage / Not directly connected to the mains voltage: MLS, Base of the light source (or other electrical interface): G13, Networked light source (CLS): No, Color-matched light source: No, Enclosure: No, Light source with high luminous density: No, Anti-glare shield: No, Similar color temperature